1 Material specification
2 ENDUROFRAME® Rollformed sections
- 2.1 Cee sections
- 2.2 U Sections
- 2.3 Lintels
- 2.4 Accessory Components
- 2.5 Brackets
- 2.6 Bracing and Blocking
- 2.7 Beams & Bearers
- 2.8 Tie down anchor

Material specification

ENDUROFRMAME® sections are roll-formed from TRUECORE^® steel complying with AS1397:2011. The standard ENDUROFRMAME® sections are shown below, the number prefixed with G indicates minimum yield stress in MPa; and the number prefixed with AZ or AM indicates minimum coating mass in g/m2.

0.55mm BMT, TRUECORE® G550 AM150 steel
0.75mm BMT, TRUECORE® G550 AM150 steel
1.00mm BMT, TRUECORE® G550 AM150 steel
1.20mm BMT, TRUECORE® G500 AM150 steel

ENDUROFRAME® Rollformed sections

Cee sections

Cee Section Profile

Part No.	BMT	D	B1	B2	L	Feed Width mm	Section Type	Usage
	mm	mm	mm	mm	mm	Feed Width mm	Section Type	Truss chords	Truss webs	Rafter chord/ Common rafters*	Studs
C6455ra	0.55	64	40mm	38mm	8	152	Ribbed	No	No	No	Yes
C6475ra	0.75	64			8	152	Ribbed	No	No	No
C6410ra	1.0	64			8	152	Ribbed	No	No	No
C7055ra	0.55	70			8	158	Ribbed	No	Yes	No
C7075ra	0.75	70			8	158	Ribbed	Yes	Yes	Yes
C7010ra	1.00	70			8	158	Ribbed	Yes	Yes	Yes
C7012ra	1.20	70			8	158	Ribbed	No	No	No
C7555ra	0.55	75			8	163	Ribbed	No	Yes	No
C7575ra	0.75	75			8	163	Ribbed	Yes	Yes	Yes
C7510ra	1.00	75			8	163	Ribbed	Yes	Yes	Yes
C7512ra	1.20	75			8	163	Ribbed	Yes	Yes	Yes
C9055ra	0.55	90			9	178	Ribbed	No	Yes	No
C9075ra	0.75	90			9	178	Ribbed	Yes	Yes	Yes
C9010ra	1.00	90			9	178	Ribbed	Yes	Yes	Yes
C9012ra	1.20	90			9	178	Ribbed	Yes	Yes	Yes

U Sections

U Section Profile

Part Code	Base Metal Thickness	D	B1	B2	Feed width mm
	mm	mm	mm	mm
U644455G550	0.55	67.5	43	45	152
U644475G550	0.75	67.5	43	45	152
U644410G550	1.00	67.5	43	45	152
U704455G550	0.55	73.5	43	45	158
U704475G550	0.75	73.5	43	45	158
U704410G550	1.00	73.5	43	45	158
U754455G550	0.55	78.5	43	45	163
U754475G550	0.75	78.5	43	45	163
U754410G550	1.00	78.5	43	45	163
U754412G550*	1.20	78.5	43	45	163
U904475G550	0.75	93.5	43	45	178
U904410G550	1.00	93.5	43	45	178
U904412G550*	1.20	93.5	43	45	178

*These 2 products are using 500MPa coil.

Lintels

Picture	Size	Application	Part No.
	200 x 35 x 1.5	Single lintel used to resist roll-over of floor trusses at ends.

Accessory Components

Product	Base Metal Thickness (mm)	Grade of Steel	Coating
Angle Lintel 200 x 35 mm	1.0 1.5	G550 G450	AZ150 AZ150/ Z275
Angle Trim 35 x 35	0.75 1.00	G550 G550	AZ150 AZ150
Bath Rail	Bath Rail An additional structural member of a wall panel set into studs to provide a recess for a bath. Bath rails are usually factory-fitted but may be supplied loose.
Shower Rail	Shower Rail An additional structural member of a wall panel that is set into the bottom of studs to provide a recess for a shower tray. A shower rail is usually factory-fitted but may be supplied loose.
Accessory	Material
Electrical Grommet 28mm	Nylon 6 - Black